Publications of D.B. Bogy


Last updated: 10/30/07

NOTE: If present, the notation [CML Blue Report 9xxx] indicates which CML Blue Report subsequently became the published paper listed here. The CML report is the earlier version of this paper. This cross-reference is a project in progress.

  1. (with J.J.W. Rogers), "A Study of Grain Contacts in Granitic Rocks," Science, Vol. 127, 3296, pp. 470-471, 1958.
  2. (with P.R. Paslay), "Drill String Vibrations Due to Intermittent Contact of Bit Teeth," Transactions, ASME, Series B, Vol. 85, pp. 187-194, 1963.
  3. (with P.R. Paslay), "An Evaluation of the Fixed Point Method of Vibration Analysis for a Particular System with Initial Damping," Transactions, ASME, Series B, Vol. 85, pp. 233-236, 1963.
  4. (with P.R. Paslay), "Buckling of Drill Pipe in an Inclined Hole," Transactions, ASME, Series B, Vol. 86, pp. 214-220, 1964.
  5. (with P.R. Paslay), "On the Buckling of Columns," Transactions, ASME, Series B, Vol. 86, pp. 252-257, 1964.
  6. (with P.R. Paslay), "The Stability of a Circular Rod Laterally Constrained to be in Contact with an Inclined Circular Cylinder," Journal of Applied Mechanics, Vol. 31, pp. 605-610, 1964.
  7. "An 'Optimal' Solution of Saint-Venant's Flexure Problem for a Circular Cylinder," Journal of Applied Mechanics, Vol. 34, pp. 175-183, 1967.
  8. (with E. Sternberg), "The Effect of Couple-Stresses on Singularities Due to Discontinuous Loadings," International Journal of Solids and Structures, Vol. 3, pp. 757-770, 1967.
  9. (with E. Sternberg), "The Effect of Couple Stresses on the Corner Singularities Due to an Asymmetric Shear Loading, International Journal of Solids and Structures, Vol. 4, pp.159-174, 1968.
  10. "Edge-Bonded Dissimilar Orthogonal Elastic Wedges Under Normal and Shear Loading," Journal of Applied Mechanics, Vol. 35, pp. 460-466, 1968.
  11. "Elastic-Plastic Plane-Strain Solutions with Separable Stress Fields," Journal of Applied Mechanics, ASME, Vol. 36, pp. 528-532, September, 1969.
  12. (with P.M. Naghdi), "On Heat Conduction and Wave Propagation in Rigid Solids," Journal of Mathematical Physics, Vol. 11, No. 3, pp. 917-923, March, 1970.
  13. "Elastostatic Solutions on Bonded Half Planes of Dissimilar Materials," Journal of Applied Mechanics, ASME, Vol. 37, pp. 220-223, March, 1970.
  14. "On the Problem of Edge-Bonded Elastic Quarter-Planes Loaded at the Boundary," International Journal of Solids and Structures, Vol. 6, pp. 1287-1313, August, 1970.
  15. "Two Edge-Bonded Elastic Wedges on Different Materials and Wedge Angles Under Surface Tractions," Journal of Applied Mechanics, ASME, Vol. 38, No. 2, pp. 377-386, June, 1971.
  16. (with K.C. Wang) "Stress Singularities at Interface Corners in Bonded Dissimilar Isotropic Elastic Materials," International Journal of Solids and Structures, Vol. 7, pp. 993-1005, November, 1971.
  17. "Stress Concentrations at Edge Dislocation Pile-ups Against a Material Interface," Scripta Metallurgica, Vol. 5, pp. 991-996, November, 1971.
  18. "On the Plane Elastostatic Problem of a Loaded Crack Terminating at a Material Interface," Journal of Applied Mechanics, ASME, Vol. 38, No. 4, pp. 911-918, December, 1971.
  19. (with M. Hamstad) "Elastostatic Solution for a Circular Membrane Bonded to a Half-Space Under Plane Loading, "International Journal of Solids and Structures, Vol. 8, pp. 1-28, January, 1972.
  20. "The Plane Solution for Anisotropic Elastic Wedges Under Normal and Shear Loading," Journal of Applied Mechanics,39, 4, 1972.
  21. "The Plane Elastostatic Solution for a Symmetrically Loaded Crack in a Strip Composite," International Journal of Engineering Science, 11, pp. 985-996, 1973.
  22. (with M.C. Kuo) "Plane Solutions for the Displacement and Traction-Displacement Problems for Anisotropic Elastic Wedges," Journal of Applied Mechanics, 41, 197-202, 1974.
  23. (with M.C. Kuo) "Plane Solutions for Traction Problems on Orthotropic Unsymmetrical Wedges and Symmetrically Twinned Wedges," Journal of Applied Mechanics, 41, 203-208, 1974.
  24. (with J.H. Greenberg and F.E. Talke) "The Steady Solution for Circumferentially Moving Loads on a Thin Cylindrical Elastic Shell," IBM Journal of Research and Development, 18, 5, 395-400, 1974.
  25. (with K.C. Wang) "Plane Steady Vibration of an Orthogonal Elastic Wedge," Journal of Elasticity, 4, 1, 1-16, 1974.
  26. (with K.C. Wang) "Plane Steady Vibration of an Elastic Wedge," Journal of Elasticity, 5, 1, 15-30, 1975.
  27. "The Shrink-Fit of a Cylindrical Shell Onto a Discontinuous Mandrel," Journal of Applied Mechanics, 41, 4, 959-962, 1974.
  28. (with G.G. Adams) "A Note on a Paper by G.D. Gupta," Journal of Applied Mechanics, 42, 1, 224, 1975.
  29. "The Plane Solutions for Joined Dissimilar Elastic Semi-Stripe Under Tension," Journal of Applied Mechanics, 42, 1, 93-98, 1975.
  30. (with G.G. Adams), "Steady Solutions for Moving Loads on Elastic Beams with One-Sided Constraints," Journal of Applied Mechanics, 42, 4, 800-805, 1975.
  31. "Solution of the End Problem for a Semi-Infinite Elastic Strip," Zeitschrift fur Angewandte Mathematik und Mechanik, 26, 749-769, 1975.
  32. (with G.G. Adams), "Bending of a Bimaterial Strip," International Journal of Solids and Structures, 12, 4, 239-249, 1976.
  33. (with G.G. Adams) "The Plane Solution for the Elastic Contact Problem of a Semi-Infinite Strip and Half-Plane," Journal of Applied Mechanics, 43, 849-854, 1976.
  34. (with J. Fromm and F.E. Talke), "Exit Region Control Source Flow Between Finite, Parallel Co-Rotating Disks," The Physics of Fluids, 20, 176-186, 1977.
  35. (with G.G. Adams), "Some Singular Elastostatic Solutions for Bimaterial Semi-Infinite Strip Composites," Proc. 6th Canadian Cong. Applied Mechanics, 23-24, 1977.
  36. (with G.G. Adams), "The Plane Symmetric Contact Problem for Dissimilar Elastic Semi-Infinite Strips of Different Widths," J. of Applied Mechanics, 44, 604-610, 1977.
  37. "Use of One-Dimensional Cosserat Theory to Study Instability in a Viscous Liquid Jet," The Physics of Fluids, 21, 190-197, 1978.
  38. (with F.E. Talke), "Steady Axisymmetric Solutions for Pressurized Rotating Flexible Disk Packs," IBM Journal of Research and Development, 22, 2, 179-184, 1978.
  39. "Adhesion of Bimaterial Elastic Strips," J. Eng. Mech. Div., Proc. ASCE, 104, EM4, 911-920, 1978.
  40. "Wave Propagation and Instability in a Circular Semi-Infinite Liquid Jet Harmonically Forced at the Nozzle," J. of Applied Mechanics, 45, 3, 469-474, 1978.
  41. (with R.C. Benson) "Deflection of a Very Flexible Spinning Disk Due to a Stationary Transverse Load," J. of Applied Mechanics, 45, 3, 636-642, 1978.
  42. "Break-up of a Liquid Jet: Second Perturbation Solution for One-dimensional Cosserat Theory," IBM Journal of Research and Development, 23, 1, 87-92, January, 1979.
  43. "Drop Formation in a Liquid Jet," Annual Review of Fluid Mechanics, Vol. 11, 207-228, 1979.
  44. "Break-up of a Liquid Jet: Third Perturbation Cosserat Solution," The Physics of Fluids, 22, 2, 224-230, February,1979.
  45. (with J.E. Fromm and F.E. Talke) "A Numerical and Experimental Study of the Bistable-Unstable Transition in Pressurized Flexible Disk Files," IBM Journal of Research and Development, 23, 4, 437-449, July, 1979.
  46. (with N. Bugdagci and F.E. Talke) "Experimental Determination of Creep Functions for Thin Orthotropic Polymer Films," IBM Journal of Research and Development, 23, 4, 450-458, July, 1979.
  47. (with R. Kant) "The Elastostatic Axisymmetric Problem of a Cracked Sphere." Journal of Applied Mechanics, 47, 3, 538-544, September, 1980.
  48. (with R. Kant) "The Elastostatic Axisymmetric Problem of a Cracked Sphere Embedded in a Dissimilar Matrix," Journal of Applied Mechanics, 47, 3, 545-550, September, 1980.
  49. (with S.J. Shine and F.E. Talke) "Finite Difference Solution of the Cosserat Fluid Jet Equations," Journal of Computational Physics, 38, 3, 294-326, 1980.
  50. "Steady Draw-Down of a Liquid Jet Under Surface Tension and Gravity," Journal of Fluid Mechanics, 105, 157-176, 1981.
  51. (with N. Bugdayci) "A Two-Dimensional Theory for Piezoelectric Layers Used in Electro-Mechanical Transducers - I Derivation," International Journal of Solids and Structures, 17, 12, 1159-1178, 1981.
  52. (with N. Bugdayci) "A Two-Dimensional Theory for Piezoelectric Layers Used in Electro-Mechanical Transducers - II Applications," International Journal of Solids and Structures, 17, 12, 1179-1202, 1981.
  53. (with Y.C. Angel) "Scattering of Rayleigh Waves by a Plate Attached to a Half-Space Through a Viscous Couplant," Journal of Applied Mechanics, 48, 881-888, 1981.
  54. (with S.E. Bechtel and F.E. Talke) "Impact of a Liquid Drop Against a Flat Surface," IBM Journal of Research and Development, 25, 6, 963-971, 1981.
  55. (with D.K-K. Miu) "Transient Voltage Across Axisymmetrically Loaded Piezoelectric Disks with Electroded Faces," Journal of Acoustical Society of America, 71, 2, 487-297, 1982.
  56. (with S.E. Bechtel) "Electro-Mechanical Analysis of Non-Axisymmetrically Loaded Piezoelectric Disks with Electroded Faces," J. Acoust. Soc. AM., 72, 1498-1507, 1982.
  57. (with S.M. Gracewski) "Reflection Coefficient for Plane Waves in a Fluid Incident on a Layered Elastic Halfspace," J. Applied Mech., 50, 405-414, 1983.
  58. (with S.M. Gracewski) "On the Plane Wave Reflection Coefficient and Nonspecular Reflection of Bounded Beams for Layered Halfspaces Under Water," J. Acoust., Soc. Am., 74, 691-599, 1983.
  59. (with N. Bugdayci and F.E. Talke) "Axisymmetric Motion of Radially Polarized Piezoelectric Cylinders Used in Ink Jet Printing," IBM J. Res. Dev., 27, 171-179, 1983.
  60. (with R.T.K. Su) "Effect of Mounting Constraints on the Response of Piezoelectric Disks," J. Acoust. Soc. Am. 73,2210-2215, 1983.
  61. (with F.E. Talke) "Experimental and Theoretical Study of Wave Propagation Phenomena in Drop-On-Demand Ink Jet Transducers," IBM J. Res. Dev. 28, 314-321, 1984.
  62. (with S.M. Gracewski) "Nonspecular Reflection of Bounded Acoustic Beams from the Liquid-Solid Interface of Two Elastic Layers on a Halfspace Under Water," Int. J. Solids Struct.,20, 8, 747-760, 1984.
  63. (with S.E. Bechtel) "Interaction of a Piezoelectric Transducer with an Elastic Half-Space," Int. J. Solids Struct., 20, 809-828, 1984.
  64. (with D.K. Miu, G. Bouchard, and F.E. Talke) "Dynamic Response of a Winchester-Type Slider Measured by Laser Doppler Interferometry," IEEE Trans. on Magnetics, MAG-20, 5, 927, Sept. 1984.
  65. (with H.J. Yang) "Elastic Wave Scattering from an Interface Crack in a Layered Half Space," J. Applied Mech., 52, 42-50, March, 1985.
  66. (with G. Bouchard, D.K. Miu, and F.E. Talke) "On the Dynamics of Winchester and 3370-type Sliders Used in Magnetic Recording Disk Files," Tribology and Mechanics of Magnetic Storage Systems, ASLE Special Publication SP-16, 85-89, Oct. 1984.
  67. (with C. Garcia-Suarez and F.E. Talke) "Use of an Upwind Finite Element Scheme for Air Bearing Calculations," Tribology and Mechanics of Magnetic Storage Systems, ASLE Special Publication SP-16, 90-96, Oct. 1984.
  68. (with F.E. Talke) "Creep of a Biaxially Oriented Polymer Disk Due to Forces of Rotation," Tribology and Mechanics of Magnetic Storage Systems, ASLE Special Publication SP-16, 115-125, Oct. 1984.
  69. (with G. Bouchard) "Experimental Measurement of Scattered Surface Waves Using a Laser-Doppler Technique," J. Acoust. Soc. AM., 77, (3), 1003-1009, March, 1985.
  70. (with G. Bouchard and F.E. Talke) "An Experimental Comparison of the Head/Disk Interface Dynamics in 5 1/4 and 8 inch Disk Drives," IBM J. Res. Develop. 29, 316-323, May, 1985.
  71. (with F.E. Talke) "Laser Doppler Interferometry on Magnetic Recording Systems" (Invited Sectional Paper in 1985 International Magnetics Conference). IEEE Trans. on Magnetics, MAG-21, 1332-1337, Sept. 1985.
  72. (with G. Bouchard and F.E. Talke) "Use of a Laser Doppler Anemometer for Studying In-Plane Motions of Sliders in Magnetic Disk Files," Tribology and Mechanics of Magnetic Storage Systems, ASLE Special Publication SP-19, 87-92, Oct.1985.
  73. (with G. Bouchard, W.-R. Chang and F.E. Talke) "Use of the Laser-Doppler Vibrometer to Measure the Surface Topography of Magnetic Disks," Wear, 107, 227-244, 1986.
  74. (with S.M. Gracewski) "Elastic Wave Scattering from an Interface Crack in a Layered Half Space Submerged in Water: Part I: Applied Tractions at the Liquid-Solid Interface", Journal of Applied Mechanics, 108, 326-332, June, 1986.
  75. (with S.M. Gracewski) "Elastic Wave Scattering from an Interface Crack in a Layered Half Space Submerged in Water: Part II: Incident Plane Waves and Bounded Beams", Journal of Applied Mechanics, 108, 333-338, June, 1986.
  76. (with S.E. Bechtel and M.G. Forest) "A One-dimensional Theory for Viscoelastic Fluid Jets, with Application to Extrudate Swell and Draw-down under Gravity", Journal of Non Newtonian Fluid Mechanics, 21, 273-308, 1986.
  77. (with D.K. Miu) "Theoretical and Experimental Investigation of the Dynamic Flying Characteristics of 3370-Type Sliders in 5-1/4 Inch Disk Drives", IEEE Transactions on Magnetics, MAG-22, 1025-1027, Sept. 1986.
  78. (with D.K. Miu) "Dynamics of Gas-Lubricated Slider Bearings in Magnetic Recording Disk Files-Part I: Experimental Observations", Journal of Tribology, 108, 584-588, Oct. 1986.
  79. (with D.K. Miu) "Dynamics of Gas-Lubricated Slider Bearings in Magnetic Recording Disk Files-Part II: Numerical Simulation", Journal of Tribology, 108, 589-593, Oct. 1986.
  80. (with F.E. Talke) "Mechanics-related problems of magnetic recording technology and ink-jet printing" in Applied Mechanics Problems in Industry, Applied Mechanics Reviews, 39, 1665-1677, Nov. 1986.
  81. (with T.W. Shield and F.E. Talke), "A Numerical Comparison of One-Dimensional Fluid Jet Models Applied to Drop-On-Demand Printing", Journal of Computational Physics, 67, 2, pp. 327-347, Dec. 1986.
  82. (with W.K. Shi and L.Y. Zhu), "Use of Readback Signal Modulation to Measure Head/Disk Spacing Variations in Magnetic Recording Disk Files", IEEE Transactions on Magnetics, MAG-23, pp. 233-240, Jan. 1987.
  83. (with T.W. Shield and F.E. Talke), "Drop Formation by DOD Ink-Jet Nozzles: A Comparison of Experiment with Numerical Simulation", IBM Journal of Research and Development, 31, pp. 96-110, Jan. 1987.
  84. (with W.R. Chang and I. Etsion), "An Elastic-Plastic Model for the Contact of Rough Surfaces", Journal of Tribology, 109 pp. 257-263, April 1987.
  85. (with H.A. Downey) "The Normal Impact on an Elastic Half Space of an Elastic Rod-Mass System", Journal of Applied Mechanics, 54, pp. 359-366, June 1987.
  86. (with H.A. Downey) "The Normal Impact of an Elastic Rod-Mass System on a Viscoelastic Half Space", Journal of Applied Mechanics, 54, pp. 367-372, June 1987.
  87. (with F.E. Talke) "Head-Medium Interface", Magnetic Recording Vol I: Technology (ed. C.D. Mee and E.D. Daniel), Chapter 7, pp. 427-507, McGraw-Hill Book Company, 1987.
  88. (with L-Y. Zhu) "A Comparison of Head-to-Disk Spacing Fluctuation on Hard and Stretch-Surface Recording Disks", IEEE Transactions on Magnetics, MAG-23, No. 5, 3447, 1987.
  89. (with L-Y. Zhu and W-K. Shi) "Simultaneous Measurement of Disk Vibrations and Slider Bearing Response in an Operating Magnetic Disk File", Tribology and Mechanics of Magnetic Storage Systems, Volume III, ASLE Special Publication SP-21, 160-163, 1987.
  90. (with H-C. Tsai) "Critical Review: Characterization of Diamondlike Carbon Films and Their Application as Overcoats on Thin-Film Media for Magnetic Recording", Journal of Vacuum Science and Technology, A5 (6), 3287, 1987.
  91. (with W.R. Chang and I. Etsion) "Adhesion Model for Metallic Rough Surfaces", Journal of Tribology, 110, 50, 1988.
  92. (with W.R. Chang and I. Etsion) "Static Friction Coefficient Model for Metallic Rough Surfaces", Journal of Tribology, 110, 57, 1988.
  93. (with H-C. Tsai, M.K. Kundmann, D.K. Veirs, M.R. Hilton, and S.T. Mayer), "Structure and Properties of Sputtered Carbon Overcoats on Rigid Magnetic Media Disks", Journal of Vacuum Science and Technology, A, 2307-2315, 1988.
  94. (with T. Yamada) "Load-Unload Slider Dynamics in Magnetic Disk Drives", IEEE Transactions on Magnetics, MAG-25, 2742-2744, 1988.
  95. (with L-Y. Zhu and K.F. Hallamasek) "Measurement of Head/ Disk Spacing with a Laser Interferometer", IEEE Transactions on Magnetics, MAG-25, 2739-2741, 1988
  96. (with O.J. Ruiz) "A Comparison of Slider Bearing Simulations Using Different Models", IEEE Transactions on Magnetics, MAG-25, 2754-2756, 1988.
  97. (with J. Streator and I. Etsion) "The Effect of Lubrication on the Static and Low-Speed Dynamic Friction in Thin Film Magnetic Disks", Tribology and Mechanics of Magnetic Storage Systems, Volume V, STLE Special Publication SP-25, 24-29, 1988.
  98. (with H.A. Downey) "The Normal Impact of a Rod-Mass System on a Viscoelastic Layered Half Space", Journal of Applied Mechanics, 55, 879-886, 1988.
  99. (with T.W. Shield) "Multiple Region Contact Solutions for a Flat Indenter on a Layered Elastic Half Space: Plane-Strain Case", Journal of Applied Mechanics, 56, 251-262, 1989.
  100. (with T-G. Jeong) "Natural Frequencies of Sliders and Transducers Used to Detect Slider-Disk Contacts", IEEE Transactions on Magnetics, MAG 26, 3725-3727, Sept. 1989.
  101. (with L-Y. Zhu) "Head-Disk Spacing Fluctuation Due To Disk Topography in Magnetic Recording Hard Disk Files", Tribology and Mechanics of Magnetic Storage Systems, STLE Special Publication SP-26, 160-167, 1989.
  102. (with L-Y. Zhu) "A Multi-Channel Laser Interferometer and Its Use To Study Head-Disk Interface Dynamics in Magnetic Disk Drives", Tribology and Mechanics of Magnetic Storage Systems, STLE Special Publication SP-26, 168-179, 1989.
  103. (with T.W. Shield) "Some Axisymmetric Problems for Layered Media: Part I, Multiple Region Contact Solutions for Simply Connected Indenters", Journal of Applied Mechanics, Vol. 56, 798, 1989.
  104. (with T.W. Shield) "Some Axisymmetric Problems for Layered Media: Part II, Solutions for Annular Indenters and Cracks", Journal of Applied Mechanics, Vol. 56, 807, 1989.
  105. (with Cho, N-H., K.M. Krishnan, D.K. Veirs, M.D. Rubin, C.B. Hopper, B. Bhushan) "Power Density Effects in the Physical and Chemical Properties of Sputtered Diamond-like Carbon Thin Films", Mat. Res. Soc., Symp. Proc., Vol. 164, 309, 1989.
  106. (with H.M. Stanley and I. Etsion) "Adhesion of Contacting Rough Surfaces in the Presence of Sub-Boundary Lubrication", Journal of Tribology, Vol. 112, 98, 1990.
  107. (with T-G. Jeong), "Slider-Disk Interactions During the Load-Unload Process", IEEE Trans. Magn., Vol. 26, No. 5, 2490-2492, September, 1990.
  108. (with M. Suk and B. Bhushan), "Role of Disk Surface Roughness on Slider Flying Height and Air-Bearing Frequency", IEEE Trans. Magn., Vol. 26, No. 5, 2493-2495, September, 1990.
  109. (with O.J. Ruiz), "A Numerical Simulation of the Head-Disk Assembly in Magnetic Hard Disk Files: Part I-Component Models", Journal of Tribology, Vol. 112, 593-602, Oct. 1990.
  110. (with O.J. Ruiz), "A Numerical Simulation of the Head-Disk Assembly in Magnetic Hard Disk Files: Part II-Solution of the Coupled System", Journal of Tribology, Vol. 112, 603-613, Oct. 1990.
  111. (with Cho, N-H, K.M. Krishnan, K.D. Veirs, M.D. Rubin, C.B. Hopper, and B. Bhushan) "Chemical Structure and Physical Properties of Diamond-Like Amorphous Carbon Films Prepared by Magnetron Sputtering", J. Mat. Res., Vol. 5, No. 11, 2543-2554, Nov. 1990.
  112. (with Streator, J.L. and B. Bhushan) "Lubricant Performance in Magnetic Thin Film Disks with Carbon Overcoat, Part I: Dynamic and Static Friction", Journal of Tribology, Vol. 113, No. 1, 22-31, January 1991.
  113. (with Streator, J.L. and B. Bhushan) "Lubricant Performance in Magnetic Thin Film Disks with Carbon Overcoat, Part II: Durability", Journal of Tribology, Vol. 113, No.1, 32-37, January 1991.
  114. (with Strom, B.C., C.S. Bhatia and B. Bhushan) "Tribochemical Effects of Various Gases and Water Vapor on Thin Film Magnetic Disks with Carbon Overcoats", Journal of Tribology, Vol. 113, No. 4, 689-693, October, 1991.
  115. (with B. Marchon and M. Khan) "Scanning Tunneling Microscopy Studies of Carbon Overcoats of Thin Film Media", IEEE Trans. Magn., Vol. 27, 6, 5067-5069, November, 1991
  116. (with E. Cha) "Numerical Simulation and Animation of Head-Disk-Assembly Dynamics", IEEE Trans. Magn., Vol. 27, 6, 5036-5038, November, 1991
  117. (with M. Suk and T. Ishii) "Comparison of Flying Height Measurements Between Multichannel Laser Interferometry and Capacitance Slider", IEEE Trans. Magn., Vol. 27, 6, 5048-5050, November, 1991
  118. (with T.G. Jeong) "Measurement of Slider-Disk Contacts During Dynamic Load-Unload", IEEE Trans. Magn., Vol. 27, 6, 5073-5075, November 1991.
  119. (with K. Ono and J.-S. Chen) "Stability Analysis of the Head-Disk Interface in a Flexible Disk Drive", J. Appl. Mech., Vol.58, No. 4, 1005-1014, Dec. 1991.
  120. (with Suk, M. and Ishii, T.) "The Influence of Air-Bearing Surface Geometry on the Dynamics of Sliders", J. Tribology Vol. 114, 26-31, 1992.
  121. (with Streator, J.L.) "Accounting for Transducer Dynamics in the Measurement of Friction", J. Tribology, Vol. 114, 86-94, 1992.
  122. (with N-H. Cho, D.K. Veirs, J.W. Ager, M.D. Rubin, C.B. Hopper),"Effects of Substrate Temperature on Chemical Structure of Amorphous Carbon Films", J. Appl. Physics, Vol. 71, (5), 2243-2256, March, 1992.
  123. (with J.-S. Chen) "Mathematical Structure of Modal Interactions in a Spinning Disk-Stationary Load System", J. Appl. Mech. Vol. 59, No.2, pt 1, 390-397, June 1992.
  124. (with J.-S. Chen) "Effects of Load Parameters on the Natural Frequencies and Stability of a Flexible Spinning Disk with a Stationary Load System", J. Appl. Mech. Vol. 59, No.2, pt 1,S230-235, June 1992.
  125. (with C-J. Lu) "The Influence of Thermal Deformation on the Contact Temperature of Sliding Asperities", J. Appl. Mech. Vol. 59, No.2, pt 2, S102-106, June 1992.
  126. (with T.G. Jeong) "An Experimental Study of the Parameters That Determine Slider-Disk Contacts During Dynamic Load- Unload", J. of Tribology, Vol, 114, 507-514, July, 1992.
  127. "Surface Modification and Measurement Using a Scanning Tunneling Microscope With a Diamond Tip", J. of Tribology, Vol. 114, 493-498, July, 1992.
  128. (with M. Suk and T. Ishii) "Evaluation of Capacitance Displacement Sensors Used for Slider-Disk Spacing Measurements in Magnetic Disk Drives", IEEE Trans. Magn., Vol. 28, No. 5, 2542-2544, Sept. 1992.
  129. (with T.-G. Jeong) "Unloaded Slider Vibrations Excited by Air Flow Between Slider and Rotating Disk", IEEE Trans. Magn., Vol. 28, No. 5, 2539-2541, Sept. 1992.
  130. (with T. Maeno) "Effect of the Hydrodynamic Bearing on rotor/Stator Contact in a Ring-Type Ultrasonic Motor", IEEE Trans. on Ultrasonics, Ferro-electrics, and Frequency, Vol. 39, No. 6, Nov. 1992.
  131. (with T-G. Jeong) "Use of Electrical Resistance Methods to Detect Slider-Disk Contacts During Contact-Start-Stop and Dynamic Load-Unload", Adv. Info. Stor. Syst. Vol. 4, 1992.
  132. (with B. Strom, R.G. Walmsley, J. Brandt, and C.S. Bhatia) "Gaseous Wear Products From Lubricated Thin Film Disks", TMRC Conference, Santa Clara, CA Summer, 92, IEEE Trans, Magn., Vol. 29, No. 1, 253-258, January, 1993.
  133. (with H.M. Stanley, M. Donovan, and E. Cha) "Some Critical Tribological Issues in Contact and Near-Contact Recording", TMRC Conference, Santa Clara, CA Summer, 92 IEEE Trans, Magn., Vol. 29, No. 1, 230-233, January, 1993.
  134. (with J.-S. Chen) "Natural Frequencies and Stability of a Flexible Spinning Disk-Stationary Load System With Rigid Body Tilting", J. Appl. Mech., Vol 60, 470-477, June 1993.
  135. (with T.-G. Jeong) "Numerical Simulation of Dynamic Loading Processes in Hard Disk Drives", J. of Tribology, Vol. 115, 370-375, July, 1993.
  136. (with Z. Feng, K. Komvopoulos, I.G. Brown) "The Effect of Graphitic Carbon Films on Diamond Nucleation by Microwave Plasma Enhanced Chemical Vapor Deposition" J. Appl. Phys, Vol. 74, 2841-2849, Aug. 1993.
  137. (with H.M. Stanley) "Effects of Surface Conformity on Friction", Proceedings of the 1st International Workshop on Microtribology, Wear, Vol. 168, 1-2, 105-108, 1993
  138. (with E. Cha and M. Donovan) "Some Head-Disk Interface Tribology Issues for Near-Contact Recording on Hard Disk Drives", Proceedings of the 1st International Workshop on Microtribology, Wear, Vol. 168, 1-2, 37-42, 1993
  139. (with B.D. Strom, W.R. Walsmley, J. Brandt, and C.S. Bhatia)"Gaseous wear products from PFPE lubricant films", Proc. 1st Int. Workshop on Microtribology, Wear, Vol. 168, 1-2, 31-36,1993
  140. (with J.-S. Chen) "The Effects of a Space-Fixed Friction Force on the In-Plane Stress and Stability of Transverse Vibrations of a Spinning Disk", J. Appl. Mech., Vol. 60, 646-648, Sept. 1993.
  141. (with T. Maeno) "FE Analysis and LDA Measurement of the Dynamic Rotor/Stator Contact in a Ring-Type Ultrasonic Motor", J. of Tribology, Vol. 15, 625-631, Oct. 1993
  142. (with E.R. Kral and K. Komvopoulos) "Elastic-Plastic Finite Element Analysis of Repeated Indentation of a Half-Space by a Rigid Sphere", J. Appl. Mech., Vol. 60, 829-841, Dec. 1993.
  143. (with E. Cha) "Numerical Simulations of Spacing Variations and Asperity Contact for a Shaped Rail Slider", IEEE Trans Magn., Vol. 29, 3960-3962, Nov. 1993.
  144. (with T.G. Jeong) "Dynamic Loading Impact-Induced Demagnetization in Thin Film Media", IEEE Trans on Magn, Vol.29, 3903-3905, Nov. 1993.
  145. (with C. Wilson) "Experimental Modal Analysis of a Suspension Assembly Loaded on a Rotating Disk", ASME Journal of Vibration and Acoustics, Vol. 116, 85-92, January 1994.
  146. (with C.J. Lu and R. Kaneko) "Nanoindentation Hardness Tests Using Point Contact Microscope", J. of Tribology , Vol. 116,pp 175-180, January 1994
  147. (with X. Yun and B.J. Knapp) "Enhancement of Head-Disk Interface Durability by use of Diamond-Like Carbon Overcoats on the Slider's Rails", IEEE Trans. Magn., Vol. 30, No. 2,369-373, Mar., 1994.
  148. (with Feng, Z., Komvopoulos, K., and Brown, I.G., "A pretreatment process for enhanced diamond nucleation on smooth silicon substrates coated with hard diamond films", J. Mats. Res., V. 9, No. 8, 2148-2153, August, 1994
  149. (with F.A. DeBruyne) "Numerical Simulation of the Lubrication of the Head-Disk Interface Using a Non-Neutonian Fluid", J. of Tribology, Vol. 116, No. 3, 541-548, July, 1994.
  150. (with C. Wilson) "Modal Analysis of a Suspension System", J. Engr. Industry, Vol. 116, No. 3, 377-387, Aug. 1994.
  151. (with B. Strom, R. Walmsley, J. Brandt and C.S. Bhatia)"Tribochemical Wear of Carbon Films in Oxygen", J. Appl. Phys. Vol. 76, No. 8, 4651-4655, Oct. 1944.
  152. (with T. Maeno) "Effect of the Rotor/Stator Interface Condition Including Contact Type, Geometry, and Material on the Performance of Ultrasonic Motors", J. of Tribology, Vol. 116, 726-732, Oct. 1994.
  153. (with T-C. Fu) "Slider vibrations induced by ramp-suspension interaction during the ramp loading process", IEEE Trans. Magn. Vol. 30, 6, 4170-4172, Nov. 1994.
  154. (with Z. Feng, M.A. Brewer, K. Komvopoulos, and I.G. Brown) "Diamond nucleation on unscratched silicon substrates coated with various non-diamond carbon films by microwave plasma-enhanced chemical vapor deposition", J. Mat. Res., Vol 10, 165-174, Jan 1995.
  155. (with E. Cha) "A Numerical Scheme for Static and Dynamic Simulation of Sub-Ambient Pressure Shaped Rail Sliders", J. of Tribology, Vol. 117, 36-46, Jan. 1995.
  156. (with T.G. Jeong) "Demagnetization due to inverse magnetostriction effects in longitudinal thin film media", IEEE Trans. Magn., Vol. 31, 1007-1012, Mar. 1995.
  157. (with Z. Jiang, C.-J. Lu, and T. Miyamoto), "An Investigation on Experimental Conditions and Characteristics of a Nano-wear Test.", Wear, Vol. 181-183, 777-783, March, 1995.
  158. (with Z.Jiang, C.-J. Lu, C.S. Bhatia and T. Miyamoto) "Nanotribological Characterization of Hydrogenated Carbon Films by Scanning Probe Microscopy", Thin Solid Films, Vol. 258, 75-81, April, 1995.
  159. (with Z. Jiang) "nano-hardness, nano-friction and nano-wear of ultra-thin overcoats" Mat. Res. Soc. Symp. Proc., Vol. 356,737-748, 1995.
  160. (with E.R. Kral and K. Komvopoulos) "Finite Element Analysis of Repeated Indentation of an Elastic-Plastic Layered Medium by a Rigid Sphere: Part I- Surface Results, J. Appl. Mech., Vol. 62, 20-28, March, 1995.
  161. (with E.R. Kral and K. Komvopoulos) "Finite Element Analysis of Repeated Indentation of an Elastic-Plastic Layered Medium by a Rigid Sphere: Part II-Sub Surface Results, J. Appl. Mech., Vol. 62, 29-42, March, 1995.
  162. (with C-J. Lu) "The Effect of Tip Radius on Nano-Indentation Hardness Tests" Int. J. Sol. Struct., Vol. 32, 12, 1759-1770, May, 1995.
  163. (with C.-J. Lu, Z. Jiang and T. Miyamoto) "simultaneous measurements of surface topography and friction force by a single-head lateral force microscope", J. Tribology, Vol. 117 334-342, April, 1995.
  164. (with Z. Jiang, C-J. Lu and T. Miyamoto), "Dependence of Nano-friction and Nano-wear on Loading Force for Sharp Diamond Tips on Si, Mn-Zn Ferrite and Au", J. Tribology, Vol. 117, 328-333, April, 1995.
  165. (with C-J. Lu, Z. Jiang, and T. Miyamoto) "Development of a New Tip Assembly for Lateral Force Microscopy and Its Application to Thin Film Magnetic Media", J. Tribology, Vol. 117, 244-249, April, 1995
  166. (with C-J. Lu, Z. Jiang and T. Miyamoto) "Experimental determination of tribological properties of ultra-thin solid films", Zeit. fur Angew. Math. und Mech., Vol. 46SI, S483-S505, 1995
  167. (with C.J. Lu) Sub-microindentation Hardness Tests of Thin Film Disks Using Point Contact Microscope", AISS, Vol. 6, 163-175, 1995.
  168. (with T-C. Fu) "Slider-Disk Contacts During the Loading Process of a Ramp-Load Magnetic Disk Drive", AISS, Vol. 6, 41-54, 1995.
  169. (with T. Miyamoto, T. Serikawa, S. Hirono, Z. Jiang and R. Kaneko), "Tribological Characteristics of SiO2 Films Investigated by Scanning Probe Microscopy", IEEE Trans. Magn., Vol. 31, No. 6, 3018-3020, Nov. 1995
  170. (with Z. Jiang, C.-J. Lu, C.S. Bhatia, and T. Miyamoto)"Nanotribological Evaluations of Hydrogenated Carbon Films as Thin as 5 nm on Magnetic Rigid Disks", IEEE Trans. Magn., Vol.31, No. 6, 3015-3017, Nov.1995
  171. (with T.-C. Fu) "Drive Level Slider-Suspension Vibration Analysis and its Application to a Ramp-Load Magnetic Disk Drive." IEEE Trans. Magn., Vol. 31, No. 6, 3003-3005, Nov.1995
  172. (with M.J. Donovan) " Experimentally Observed Roughness Effects on the Air Bearing in the Psudo-Contact Spacing Regime", IEEE Trans. Magn., Vol. 31, No. 6, 2994-2996, Nov.1995
  173. (with M. O'Hara) "Robust Design Optimization Techniques for Ultra-Low Flying Sliders", IEEE Trans. Magn., Vol. 31, No. 6,2955-2957, Nov. 1995
  174. (with S. Lu, H.M. Stanley, C.S. Bhatia, and Y.-T. Hsia)"Design, Simulations, Fabrication and Measurement of a 25 nm,50% Slider, IEEE Trans. Magn., Vol. 31, No. 6, 2952-2954, Nov.1995
  175. (with B. Budaev) "Rayleigh wave scattering by a wedge", Wave Motion, 22, 239-257, Nov. 1995.
  176. (with C-J. Lu, S.S. Rosenblum, and G.J. Tessmer) "Nano-Tribological Investigations of Carbon Overcoats: Correlation with Raman Spectra", Thin Solid Films, 268, 83-90, Dec. 1995.
  177. (with Z. Feng, K. Komvopoulos, J.W. Ager III, S. Anders, A. Anders, Z. Wang and G.I. Brown) "Effect of pretreatment process parameters on diamond nucleation on unscratched silicon substrates coated with amorphous carbon films", J. Appl. Phys., 79, 1, 485-492, Jan. 1996.
  178. (with S. Lu, Y. Hu, M. O'Hara, C.S. Bhatia, and Y-T. Hsia) "Air Bearing Design, Optimization, Stability Analysis and Verification for Sub-25nm Flying", IEEE Trans Magn., Vol 32,103-109, Jan. 1996.
  179. (with T. Miyamoto, T. Yokohata, S. Miyake, and R. Kaneko)"Wear Resistance of N+-implanted Silicon Investigated by Scanning Probe Microscopy", J. Tribology, Vol. 117, 612-616,Oct. 1995.
  180. (with T.G. Jeong) "Numerical Simulation of Head-Disk Impacts During Dynamic Loading Processes", submitted to J. Tribology, Vol. 117, 602-606, Oct. 1995.
  181. (with E. Cha) "Numerical Simulation of Slider Interaction with Multiple Asperity using Hertzian Contact Model". J. of Tribology, Vol. 117, 575-579, Oct. 1995.
  182. (with C. Wilson) "An Experimental Modal Analysis Technique for Miniature Structures", J. Vibrations and Acoustics, Vol. 118,1-9, Jan. 1996
  183. (with E.R. Kral and K. Komvopoulos) "Hardness of Thin-Film Media: Scratch Experiments and Finite Element Simulations", J. Tribology, Vol. 118, 1-11, Jan. 1996
  184. (with T.-C. Fu) "Readback Signal Decrease due to Dynamic Load Head-Disk Contacts", J. Tribology, Vol. 118, 370-375, Apr.1996.
  185. (with Feng, Z, Anders, S., Anders, A. Ager, J.W and others), ”Diamond Growth on Hard Carbon Films”, Diamond and Related Mats., V. 5, 10, 1080-1086, August 1996.
  186. (with T.-C. Fu) "Dynamic Load Head-Disk Interface Durability of 50 Percent Sliders and Polished Disks", IEEE Trans. Magn, Vol. 32, 5, 3747-3749, Sept, 1996.
  187. (with M.A. O'Hara and Y. Hu) "Effects of Slider Sensitivity Optimization", IEEE Trans. Magn., Vol, 32, 5, 3744-3746, Sept, 1996.
  188. (with A.M. Allen) "Effects of Shock on the Head-Disk Interface", IEEE Trans. Magn., Vol. 32, 5, 3717-1719.
  189. (with Y. Hu) "Spacing Modulation of a Slider Flying Across a Transition Between Landing and Data Zones", IEEE Trans. Magn, Vol 32, 5, 3714-1716, Sept. 1996.
  190. (with X. Yun and C.S. Bhatia) "Wear of Hydrogenated Carbon Coated Disks by Carbon Coated and Uncoated Al2O3/TiC Sliders in Ultra High Vacuum", IEEE Trans. Magn, Vol. 32, 5, 3669-3672, Sept, 1996.
  191. (with C. Bedoy, M. Sullivan, C.Du, J.L. Chao and M. Russak)"Surface Roughness Effects on Flying Characteristics of Proximity Recording Heads", IEEE Trans. Magn., Vol, 32, 5,3660-3662, Sept, 1996.
  192. (with B. Budaev) "Rayleigh Wave Scattering by a Wedge. II", Wave Motion, Vol. 24, No. 3, 307-314, Nov. 1996.
  193. (with K. Morse, T.P. Weihs, A.V. Hamza, M. Balooch, and Z.Jiang) "Nanomechanical Properties of SiC Films Grown From C60Precursors Using Atomic Force Microscopy", J. Tribology, Vol. 119, 26-30, January, 1997.
  194. (with X. Yun, R. Hsiao, and C. Bhatia) "Hardness and Tribochemical Evaluation of Ultra-Thin CHx and CNx Overcoats", IEEE Trans. Magn, TMRC, V. 33, N. 1, PT2, 938-943, Jan. 1997.
  195. (with S. Zhang) "Effects of lift on the motion of particles in the recessed region of a slider", Phys. Fluids, V. 9, N. 5, 1265-1272, May, 1997.
  196. (with W. Huang, Garcia, A.L.) "Three-Dimensional Direct Simulation Monte Carlo Method for Slider Air Bearings", Phys. Fluids, V. 9 N. 6, 1764-1769, Jun. 1997.
  197. (with S. Zhang) "Slider Design for Controlling Contamination", J. Tribology, Vol. 119, 537-540, July, 1997.
  198. (with H. Yun and S. Bhatia) "Tribochemical Study of Hydrogenated Carbon Coatings with Different Hydrogen Content Levels in Ultra High Vacuum", J. Tribology, Vol. 119, 437-442,July, 1997.
  199. (with Y. Hu) "Flying Characteristics of a Slider over Textured Surface Disks", IEEE Trans. Magn., Vol. 33, no. 5, 3196-3198, Sept. 1997.
  200. (with S. Zhang) "Motion of Particles in a Slider/Disk Interface Including Lift Force and Wall Effect", IEEE Trans. Magn., Vol. 33, no. 5, 3166-3168, Sept. 1997.
  201. (with Q-H Zeng and L-S Chen) "A Modal Analysis Method for Slider-Air Bearings in Hard Disk Drives", IEEE Trans. Magn., Vol. 33, No.5, 3124-3126, Sept. 1997.
  202. (with Y. Hu) "Dynamic Stability and Spacing Modulation of Sub-25 nm Fly Height Sliders", J. Tribology, Vol. 119, 646-652,Oct. 1997.
  203. (with S. Anders, J. Diaz, J.W. Ager II, and Y. Lo) "Thermal stability of amorphous hard carbon films produced by cathodic-arc deposition. "J. Appl. Phys., 71, (23), 3367-3369, Dec. 1997.
  204. (with Y. Hu) "Solution of the Rarefied Gas Lubrication Equation Using an Additive Correction Based Multigrid Control Volume Method", J. Tribology, Vol. 120, 280-288, April, 1998.
  205. (with Y. Hu, P.M. Jones, P.T. Chang), “Partial Contact Air Bearing Characteristics of Tripad Sliders for Proximity Recording, J. Tribology, Vol. 120, 272-279, Apr. 1998.
  206. (with Y. Hu) "Effects of Laser Textured Disk Surfaces on a Slider's Flying Characteristics", J. Tribology, Vol. 120, 266-271, April, 1998.
  207. (with W. Huang), "An Investigation of a Slider Air Bearing with an Asperity Contact by a Three-Dimensional Direct Simulation Monte Carlo Method”, IEEE Trans. Magn., Vol. 34, 1810-1812, 1998.
  208. (with H. Takahashi), "Vibration of Head Suspensions For Proximity Recording”, IEEE Trans. Magn., Vol. 34, 1756-1758, July, 1998.
  209. (with R. Hsiao and C. Singh Bhatia) “Nanomechanical Properties of CNx Overcoats and Cathodic Arc Carbon (CAC) Films”, IEEE Trans. Magn. , Vol. 34, 1720-1722, July, 1998.
  210. (with S. Zhang) "Variation of the Heat Flux Between a Slider and Air Bearing when the Slider Flies Over an Asperity”, IEEE Trans. Magn., Vol. 34, 1705-1707, July, 1998.
  211. (with M. Staudenmann and M.J. Donovan) "A new Laser Interferometer System for Investigation of the Dynamics at the Head/Disk Interface, IEEE Trans. Magn, Vol. 34, 1696-1698, July, 1998.
  212. (with S. Lu, M. O'Hara, and S. Zhang) "Some Advanced Air-Bearing Design Issues for Proximity Recording", J. Tribology, Vol. 120, 566-570, July 1998.
  213. (with Q-H. Zeng) "Dynamics of Suspension-Slider-Air Bearing Systems: Experimental Study”, IEEE/ASME Trans. of Mechatronics Vol. 3, No. 3, 210-217, Sept. 1998.
  214. (with Wei, J., Fong W. Bhatia, C.S.) “The decomposition mechanisms of a perfluoropolyether at the head/disk interface of hard disk drives”. Tribology Letters, Vol. 5, 203-209,1998.
  215. (with Bhatia, C.S., Anders, S. and others) "Ultra-thin overcoats for the head/disk interface tribology", J. Tribology, ASME, Vol. 120, 795-799, Oct. 1998.
  216. (with B.V. Budaev) "Rayleigh wave scattering by two adhering elastic wedges" Proc. Roy. Soc. Lond., Series A, V. 454, 2949-2996, Nov. 1998.
  217. (with Q.H. Zeng) "Dynamic Characteristics of a Suspension Assembly Part 1: Modal Experiment", AISS, Vol. 8, 105-120, Dec. 1998.
  218. (with Q.H. Zeng) "Dynamic Characteristics of a Suspension Assembly Part 2: Numerical Analysis", AISS, Vol. 8, 121-133, Dec. 1998.
  219. (with Q.H. Zeng and L.S. Chen) "Air-bearing design for stable performance in proximity magnetic recording", Adv. Info. Storage Syst., Vol. 9, 121-132, Dec. 1998.
  220. (with B.V. Budaev) "Rigorous solutions of acoustic wave diffraction by penetrable wedges", J. Acoust. Soc. Amer., Vol. 105, 74-83, Jan. 1999.
  221. (with Q.H. Zeng) "Experimental Evaluation of Stiffness and Damping of Slider-Air Bearings" , J. Tribology, Vol. 121, 102-107, Jan. 1999.
  222. (with S. Zhang) “A heat transfer model for thermal fluctuations in a thin slider/disk air bearing”, Int. J. Heat and Mass Transfer, Vol. 42, 1791-1800, March, 1999. [CML Blue Report 9709]
  223. (with Q-H Zeng, M. Chapin) “Dynamics of the Unload Process for Negative Pressure Sliders, IEEE Trans. Magn., Vol. 35, No. 2, 916-920, March, 1999. [CML Blue Report 9803]
  224. (with C. S. Bhatia, W. Fong, C-Y-Chen, J. Wei, and others),“Tribo-Chemistry at the Head/Disk Interface,” IEEE Trans. Magn., Vol. 35, No. 2, 910-915, March, 1999
  225. (with Q-H. Zeng) “Slider Air Bearing Designs for Load/Unload Applications”, IEEE Trans. Magn., Vol. 35, No. 2, 746-751, March 1999.
  226. (with Q.H. Zeng) "Stiffness and Damping Evaluation of Air Bearing Sliders and New Designs with High Damping", J.Tribology, Vol. 121, 341-347, April, 1999. [CML Blue Report 9702]
  227. (with R.Y., Lo) “Compensating for elastic deformation of the indenter in hardness tests of very hard materials” J. Mater. Res., Vol. 14, No. 6,pp. 2276-2282, June 1999. [CML Blue report 9805]
  228. (with Q.H. Zeng) "Dynamics experiment and analysis of a hard disk drive", JOURNAL OF VIBRATION AND CONTROL, 1999 JUL, V5 N4:535-557. [CML Blue Report 9617]
  229. (with C-Y. Chen, W. Fong, C.S. Bhatia) "Lubricant Thickness Effect on Tribological Performance of ACOL Lubricated Disks with Hydrogenated Overcoats", Tribology Letters, Vol. 7, 1, 1-10, Oct. 1999.
  230. (with A. Anders, T. Stammler, Fong, W, and C.S. Bhatia) "Investigation of slider surfaces after wear using photoemission electron microscopy", JOURNAL OF VACUUM SCIENCE & TECHNOLOGY, A-VACUUM SURFACES AND FILMS, 1999 SEP-OCT, V17 N5:2731-2736.
  231. (with S. Anders, T. Stammler, W. Fong, C-Y. Chen, C.S. Bhatia and J. Stohr) "Study of Tribochemical Processes on Hard Disks Using Photoemission Electron Microscopy", J. Tribology, Vol. 121, 961-967, Oct. 1999.
  232. (with S. Zhang), "Thermal Response of a Magneto-Resistive Head When it Flies Over an Asperity", J. Tribology, Vol. 121, 975-979, Oct. 1999.
  233. (with Q.H. Zeng) "Effects of Suspension Limiters on the Dynamic Load/Unload Process: Numerical Simulation", IEEE Trans. Magn, Vol. 35, No. 5, 2490-2492, Sept. 1999
  234. (with L. Wu) "Unstructured Triangular Mesh Generation Techniques and a Finite Volume Numerical Scheme for Slider Air Bearing Simulation with Complex Shaped Rails", IEEE Trans. Magn, Vol. 35, No. 5, 2421-2423, Sept. 1999.
  235. (with Q.H. Zeng and M. Chapin) "Two Calibration Methods of AE Measurement Channels for Slider-Disk Contact Detection", IEEE Trans. Magn, Vol. 35, No. 5, 2367-2369, Sept. 1999.
  236. (with B. Budaev) "Rayleigh wave scattering in a wedge with mixed boundary conditions", Proc. Roy. Soc. Lond., A, Vol 455, 3967-3995. Nov. 1999.
  237. (with Q-H. Zeng) "A simplified 4-DOF suspension model for dynamic load/unload simulation and its application. J. Tribology, Vol. 122, 274-279, Jan. 2000.
  238. (with M.A. O'Hara, and Y. Hu) "Optimization of Proximity Recording Air Bearing Sliders in Magnetic Hard Disk Drives", J. Tribology, Vol. 122. 257-259, Jan. 2000.
  239. (with T-C. Fu) "Analysis of Stresses Induced by Dynamic Load Head-Disk Contacts", J. Tribology, Vol. 122. 233-237, Jan. 2000.
  240. (with Q-H. Zeng) "Effects of Certain Design Parameters on Load/Unload Performance", IEEE Trans. Magn., Vol. 36. 140-147, Jan. 2000.
  241. (Chen, CY; Fong, W; Bhatia, CS.) "Initiation of lubricant catalytic decomposition by hydrogen evolution from contact sliding on CHx and CNx overcoats", TRIBOLOGY LETTERS, 2000, V8 N1:25-34.
  242. (with W. Huang) "The Effect of the Accommodation coefficient on Slider Air Bearing Simulation", J. Tribology, Vol. 122, No. 2, 427-435, April, 2000. [CML Blue Report 9806]
  243. (with W. Huang and M. Honchi) "An Asperity Contact Model for the Slider Air Bearing", J. Tribology, Vol. 122, No. 2, 436-443, April, 2000.
  244. (with C-Y. Chen, J. Wei, W. Fong and C.S. Bhatia) "The Decomposition Mechanisms and Thermal Stability of ZDOL Lubricant on Hydrogenated Carbon Overcoats", J. Tribology, Vol. 122, No. 2, 458-464, April, 2000. [CML Blue Report 9816]
  245. (with Q-H Zeng) "Design and operating conditions for reliable load/unload systems", TRIBOLOGY INTERNATIONAL, 2000 MAY-JUN, V33 N5-6:357-366.
  246. (with C-Y. Chen and C.S. Bhatia) "Tribochemistry of monodispersed ZDOL with hydrogenated carbon overcoats. JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A-VACUUM SURFACES AND FILMS, 2000 JUL-AUG, V18 N4 PT2:1809-1817.
  247. (with L. Chen and B. Strom) "Thermal Dependence of MR Signal on Slider Flying State", IEEE Trans. on Magn., Vol. 36, 2486-2488, Sept. 2000.
  248. (with Q-H Zeng and M. Chapin) "A Force Identification Method for Slider/Disk Contact Force Measurement", IEEE Trans. on Magn., Vol. 36, 2667-2669, Sept. 2000.
  249. (with C-Y Chen, T. Cheng, and C.S. Bhatia) "Effect of the Additive X-1P on the Tribological Performance and Migration Behavior of PFPE Lubricant at the Head-Disk Interface, IEEE Trans. on Magn., Vol. 36, 2708-2710, Sept. 2000.
  250. (with L. Wu) "Unstructured adaptive triangular mesh generation techniques and finite volume schemes for the air bearing problem in hard disk drives." J. Tribology, V122 N4:761-770, Oct. 2000.
  251. (with M. Chapin), "Air bearing force measurement of pico negative pressure sliders during dynamic unload", J. Tribology, V122 N4:771-775, Oct. 2000.
  252. (with C.S. Bhatia, C.-Y. Chen, and W. Fong)"TRIBOCHEMISTRY OF ZDOL DECOMPOSITION ON CARBON OVERCOATS IN ULTRA-HIGH VACUUM (UHV)", Mat. Res. Soc. Proc. 593, (2000), 397-408.
  253. (with C-Y. Chen and C.S. Bhatia) "Effects of Backbone and Endgroup on the Decomposition Mechanisms of PFPE Lubricants and their Tribological Performance at the Head-Disk Interface", J. Tribology, Vol. 123, 364-367, April 2001.
  254. (with L. Wu) "Use of an upwind finite volume method to solve the air bearing problem of hard disk drives", Computational Mechanics, 26, 592-600, (Dec. 2000).
  255. (with B. Budaev) "Scattering of Rayleigh and Stoneley waves by two adhering elastic wedges", Wave Motion, 33, 321-337 (Mar. 2001).
  256. (with Q-H. Zeng, B.H. Thronton, and C.S. Bhatia) "Flyability and Flying Height Modulation Measurement of Sliders with Sub-10 nm Flying Heights", IEEE Trans. Magn. 37, 894-899, March, 2001.
  257. (with B. Budaev) "Probabilistic solutions of the Helmholtz equation", J. Acoust. Soc. Am.,Vol. 109, 2260-2262, May,2001.
  258. (with C-Y. Chen, C.S. Bhatia "Effect of lubricant bonding fraction at the head-disk interface", TRIBOLOGY LETTERS, 2001 MAY, V10 N4:195-201.
  259. (with L. Wu) "A Generalized Compressible Reynolds Lubrication Equation with Bounded Contact Pressure", Physics of Fluids, V13 N8:2237-2244, Aug., 2001.
  260. (with L. Wu) "Numerical Simulation of the Slider Air Bearing Problem of Hard Disk Drives by Two Multi-Dimensional Upwind Residual Distribution Schemes over Unstructured Triangular mesh," J. Comp. Phys, Vol. 172, 640-657, Sept., 2001.
  261. (with B.H. Thornton and C.S. Bhatia) "The Effects of Disk Morphology on flying-Height Modulation: Experiment and Simmultaion", IEEE Trans. Magn, TMRC, 2001, Vol. 38, No. 1 107-111, January, 2002.
  262. (with B. Budaev) "Errata to the paper "Rayleigh wave scattering by a wedge. II",[Wave Motion 24 (1996) 307-317, Wave Motion 35, 275, March 2002.
  263. (with P.M. McGuiggan, S.M. Hsu, W. Fong and C.S. Bhatia) "Friction Measurements of Ultra-Thin Carbon Overcoats in Air", J. Tribology, Vol. 124, 239-244, April, 2002.
  264. (with B. Budaev) "Application of random walk methods to wave propagation", Quart. J. Mech. Appl. Math.,V55, Pt 2, 209-226, May 2002.
  265. (with B. Budaev) "Analysis of one-dimensional wave scattering by the random walk method", J. Acoust. Soc. Amer., V. 111, 2555-2560,June 2002.
  266. (with L. Wu) "Effect of the Intermolecular Forces on the Flying Attitude of Sub-5 NM Flying Height Air Bearing Sliders in Hard Disk Drives", J. Tribology, Vol.124, 562-567, July, 2002.
  267. (with N. Tagawa) "Air Film Dynamics for Micro-Textured Flying Head Slider Bearings in Magnetic Hard Disk Drives", J. Tribology, Vol. 124, 568-574, July, 2002.
  268. with Q-H. Zeng) "Numerical Simulation of Shock Response of Disk-Suspension-Slider Air Bearing Systems in Hard Disk Drives", Microsystem Technologies, Vol.8, 289-296,August 2002.
  269. (with W. Fong, B. Thornton, H. Gross, H. Zhu, C.S. Bhatia), "Some Tribology and mechanics issues for 100 Gbit/in2", IEEE Trans Magn.,Vol. 38, 1879-1885, September, 2002.
  270. (with Takeshi Watanabe) "A Study of the Air Bearing Effect on the Lubricant Displacement Using an Optical Surface Analyzer", IEEE Trans. Magn., Vol. 38, 2138-2140, September, 2002.
  271. (with H. Zhu), "Direct Algorithm and its application to slider air bearing surface optimization", IEEE Trans Magn., Vol. 38, 2168-2170,September, 2002.
  272. (with B. Thornton and A. Nayak) “Flying Height Modulation Due to Disk Waviness of Sub-5 nm Flying Height Air Bearing Sliders”, J. Tribology, Vol. 124, 762-770, October, 2002.
  273. (with B. Budaev) "Random walk methods and wave diffraction", Int. J. Solids Struct, Vol. 39, No. 21-22, 5547-5570, October,2002.
  274. (with J. Zhang, W.Fong, T. Cheng. P. Cheng, J. Chao and C.S. Bhatia) “Relationship between the molecular structure of lubricants and their performance at the head-disk interface of hard disk drives”, WEAR, 9439 1-11, 2003.
  275. (with B. Thornton) "Non-Linear Aspects of Air Bearing Modeling and Dynamic Spacing Modulation in Sub 5 nm Air Bearings for Hard Disk Drives", IEEE Trans. Magn., TMRC2002,Vol. 39, No. 2, 722-728, March 2003.
  276. (with X.-G. Ma, K. Komvopoulos, D. Wan and Y.-S. Kim) “Effects of film thickness and contact load on nanotribological properties of sputtered amorphous carbon thin films”, WEAR, Vol 254, 1010-1018, 2003
  277. (with B. Budaev) “Probabilistic approach to the Lame equations of linear elastostatics”, Int. J. Solids. Struct., Vol 40. No. 23 pp 6285-6306
  278. (with Takeshi Watanabe) “A Study of the Lubricant Displacement Under A Flying Head Slider Caused by Slider- Disk Interaction”, IEEE Trans. Magn. Vol.39, No 5, Sept. 2003, 2477 2479.
  279. (with B. Thornton) “Head-Disk Interface Instability due to Intermolecular Forces”, IEEE Trans. Magn., Vol.39, No. 5, Sept. 2003, pp 2420 2422.
  280. with B. Budaev) “Random walk approach to wave propagation in wedges and cones”, J. Acoust. Soc. Amer., Vol. 114 (4), Oct. 2003, pp 1733-1741
  281. (with B. Budaev) “Random walk approach to wave radiation in cylindrical and spherical domains” Probabilistic Engineering Mechanics, Vol. 18, (Nov. 2003), pp 339-348.
  282. (with H. Zhu) “Hard Disk Drive Air Bearing Design: Modified DIRECT Algorithm and its Application to Slider Air bearing Surface Optimization” Tribology International (Austrib02 special issue), Vol… 37, Issue 2, Feb. 2004, pp 193-201.
  283. (with B.H. Thornton) “A Parametric Study of Head-Disk Interface Instability Due to Intermolecular Forces”, IEEETrans. Magn, Vol. 40, 1, Jan. 2004, 337-344.
  284. (with B. Budaev) “Wave scattering by surface breaking cracks and cavities”, Wave Motion, 40 (204) 163-173.
  285. (with H. Zhu) “Hard Disk Drive Air Bearing Design: Modified DIRECT Algorithm and its Application to Slider Air bearing Surface Optimization” Tribology International (Austrib02 special issue), Vol… 37, Issue 2, Feb. 2004, pp 193-201.
  286. (with B. H. Thornton) “A Numerical Study of Air-Bearing Slider Form-Factors” ASME J. Tribology, Vol. 126, 553-558, July 2004.
  287. (with X.-G. Ma and K. Komvopoulos) “Nanoindentation of polycrystalline silicon-carbide thin films studied by acoustic emission”, Applied Physics Letters, Vol. 85, 1695- 1697. Sept. 2004.
  288. (with X. Shen and Mike Suk) “Study of Transverse Flow Effects on Particle Flows and Contamination of Air Bearing Sliders” ASME J. Tribology,Vol. 126, 745-750,Oct. 2004.
  289. (with B. Budaev) “Diffraction by a plane sector”, Proc. Roy. Soc. Lond A, Vol. 460, 3529-3546 Nov. 2004.
  290. (with B. Budaev) “Diffraction of a plane wave by a sector with Dirichlet or Neumann boundary conditions” IEEE Trans. Antennas and Propagation, Vol. 53, #2, 711-718, Feb. 2005.
  291. (with V. Gupta) “Dynamics of Sub-5nm Air Bearing Sliders in the Presence of Electrostatic and Intermolecular Forces at the Head Disk Interface”, IEEE Trans. Magn., Vol. 41, 2, 610-615, Feb., 2005.
  292. (with B. Budaev) “Two Dimensional Diffraction by a Wedge With Impedance Boundary Conditions”, IEEE Trans Antennas and Propagation, Vol. 53, #6, 2073-2080, June 2005. 293. (with R. Ambekar and V. Gupta) “Experimental and Numerical Investigation of Dynamic Instability in the Head Disk Interface at Proximity.” J. Tribology, Vol. 127, 530-536, July 2005.
  293. (with J-Y. Juang)”Nanotechnology Advances & Applications in Information Storage Systems”, Microsystem Technologies,  Vol. 11, 8-10, 950-958, August, 2005.
  294. (with B. Budaev) “A probabilistic approach to wave propagation”, RADIO SCIENCE, Vol. 40, RS6S07, 1-11, August, 2005.
  295. (with Rohit P. Ambekar) “Effect of Slider Lubricant Pickup on Stability at the Head-Disk Interface”, IEEE Trans. Magn., Vol. 41, No. 10, 3028-3030, Oct. 2005.
  296. (with Jia-Yang Juang) “Controlled-Flying Proximity Sliders for Head-Media Spacing Variation Suppression in Ultralow Flying Air Bearings”, IEEE Trans. Magn., Vol. 41, No. 10, 3052-3054, Oct. 2005.
  297. (with V. Gupta) “Effect of Intermolecular Forces on the Static and Dynamic Performance of Air Bearing Sliders: Part I – Effect of initial excitations and slider form factor on the stability.”, J. Tribology, Vol. 128, No. 1, 197-202, January 2006
  298. (with V. Gupta) “Effect of Intermolecular Forces on the Static and Dynamic Performance of Air Bearing Sliders: Part II – Dependence of the Stability on Hamaker Constant, Suspension Preload and Pitch Angle.”, J. Tribology, Vol. 128, No. 1, 197-202, January 2006
  299. (with Jia_Yang Juang and Du Chen) “Alternate Air Bearing Slider Designs for Areal Density of 1 Tb/in2”, IEEE Trans. Magn., Vol. 42, No. 2, 241-246, Feb. 2006.
  300. (with B. Budaev) “Two-dimensional problems of diffraction by finite collinear structures”, J. Acoust. Soc. Amer., Vol. 119 (2), 741-750, Feb. 2006
  301. (with B. Budaev) “Diffraction of a plane electromagnetic wave by a wedge with anisotropic impedance boundary conditions”, IEEE Trans. Antennas & Propagation, Vol. 54, No. 5, 1559-1567, May 2006. 303(with S. Kirpekar) “A Study on the Efficacy of Flow Mitigation Devices in Hard Disk Drives”, IEEE Transactions on Magnetics, Vol. 42, No. 6, 1716-1729, June 2006.
  302. (with J-Y. Juang) "Nonlinear Compensator Design for Active Sliders to Suppress Head-Disk Spacing Modulation in Hard Disk Drives." IEEE/ASME Transactions on Mechatronics, Vol. 11, No. 3, 256-264, June, 2006.
  303. (with B. Budaev) “Diffraction by a convex polygon with sidewise constant impedance”, Wave Motion, Vol. 43, 631-645, Aug. 2006.
  304. (with J-Y. Juang, H. Kubotera) “Effects of Track-Seeking Motion on the Flying Attitudes of Ultralow Fling Sliders”, IEEE Trans. Magn., Vol. 42. 2522-2524, Oct. 2006.
  305. (with J-Y. Juang and C.S. Bhatia) “Design and Dynamics of Flying Height Control Slider with Piezoelectric Nanoactuator in Hard Disk Drives”, ASME J. Tribology, Vol. 129, 161-170, January, 2007
  306. (with P. Bhargava) “Numerical simulation of Operational-Shock in Small Form Factor Hard Disk Drives”, ASME J. Tribology, Vol. 129, 153-160, January, 2007
  307. (with P. Bhargava) “Effect of shock pulse width on the shock response of small form factor disk drives”, Microsystem Technologies, doi. 10-1007/s00542-006-0328-3, published on line 11/06. #46, 13 (8-10) 1107-1115, May, 2007.
  308. (with S. Kirpekar) “An alternative to CFD: piecewise linear models for frequency spectra of flow induced drag in hard disk drives”, Microsystem Technologies, doi 10.1007/s00542-006-0329-2. published on line 11/06 #68, 13 (8-10) 1171-1179, May, 2007. .
  309. (with D. Chen) “Intermolecular force and surface foughness models for air bearing simulations for sub-5 nm flying height sliders”, Microsystem Technologies, doi 10.1007/s00542-006-0317-6 published on line 11/06 #74, 13 (8-10) 1211-1217, May, 2007.
  310. (with H. Kubotera) “Numerical simulation of molecularly thin lubricant film flow due to the air bearing slider in hard disk drives”, Microsystem Technologies, doi:10.1007/s00542-006-0275-z, published on line 11/06 #102, 13 (8-10) 859-865, May, 2007.
  311. (with J-Y. Juang, R. Ambekar and C.S. Bhatia)”Fabrication and experimental study of Al2O3-TiC sliders with piezoelectric nanoactuators for flying height control”.Microsystem Technologies, doi 10.1007/s00542-006-0268-y, published on line 11/06 #109, 13 (8-10) 1107-1115, May, 2007.
  312. (B. Budaev) “Novel solutions of the Helmholtz equation and their application to diffraction”, Proc. Roy. Soc. Lond. A , 463, 1005 – 1027,April, 2007
  313. (with Du Chen) “Dynamics of Partial Contact Head Disk Interface”, IEEE Trans. Magn., Vol. 43, No. 6, 2220- 2222, June, 2007.
  314. (with J-Y. Juang) “Air-Bearing Effects on Actuated Thermal Pole-Tip Protrusion for Hard disk Drives”, ASME J. Tribology, Vol. 129, 570-578, July, 2007.
  315. (with H. Zhu) ASME J. Tribology , “Effects of Pitch Static Attitude and Roll Static attitude on the Steady Performance of Air Bearing Sliders”, ASME J. Tribology, Vol. 129, 689-694, July, 2007
  316. (with H. Kubotera) “Lubricant Migration Simulations on the Flying Head Slider air-Bearing Surface in a Hard disk Drive”, IEEE Trans. Magn., Vol. 43, No. 9, September 2007.
  317. (with H. Kubotera)” Effect of various physical factors on thin lubricant film migration on the flying head slider at the head-disk interface of hard disk drives ,JOURNAL OF APPLIED PHYSICS 102 (5): Art. No. 054309 SEP 1 2007
  318. (with B. Budaev) “On the electromagnetic singularities near the vertex of a dielectric wedge”, RADIO SCIENCE, 42, RS6S08, doi:10.1029/2006RS003578, Oct.2007.
  319. (with B. Budaev) “Diffraction by a wedge with a face of variable impedance”, Radio Sci., 42, RS6S02, doi:10.1029/2006RS003597, Oct. 2007


Conference Proceedings:
  1. (with S. Anders, Th. Stammler, C. S. Bhatia, J. Stöhr, W. Fong, and C.-Y. Chen), "Study of hard disk and slider surfaces using X-ray photoemission electron microscopy and near edge X-ray absorption fine structure spectroscopy" Mat. Res. Soc. Proc. 517 (1998) 415-420.
  2. (with S. Anders, C. S. Bhatia, W. Fong, and R. Y. Lo), "Application of cathodic arc deposited amorphous hard carbon films to the head/disk tribology", Mat. Res. Soc. Proc. 517 (1998) 371-382



Home


People


Software


Research


Campus


Misc.


Contact CML